MELLANOX CONNECTX EN MNPH28B-XSC DRIVER DETAILS:
|File Size:||7.1 MB|
|Supported systems:||Windows 7/8/10, Windows XP 64-bit, Mac OS X 10.X|
|Price:||Free* (*Free Registration Required)|
MELLANOX CONNECTX EN MNPH28B-XSC DRIVER
Hardware Devices 28 Figure 9: PCI Device 29 Figure Compatible Connector Plug and Pinout 42 Figure Connector and Cage Views 43 Figure Remove the Bracket 45 Figure Gasket Installation 46 Figure Revision Mellanox ConnectX EN MNPH28B-XSC Table 7 Table 2: Documents List 8 Table 3: LEDs 17 Table 6: Jumper Configuration 18 Table 7: Hardware and Software Requirements 26 Table HCAIt provides details as to the interfaces of the board, specifications, required software and firmware for operating the board, and relevant documentation.
Intended Audience This manual is intended for the installer and user of these cards. The manual assumes basic familiarity with InfiniBand and networks and architecture specifications.
Online Resources Web pages: Firmware download Web page: The use of Mb or Mbits small b indicates size in mega bits. Technical Support Customers who purchased Mellanox products directly from Mellanox are invited to contact us through the following methods.
ConnectX IB HCA Adapter Card with QSFP Connectors User Manual - PDF
Customers who purchased Mellanox products through a Mellanox approved reseller should first seek assistance through their reseller. Firmware and Software Updates The Mellanox support downloader contains software, firmware and knowledge database information for Mellanox products.
The cards described in this manual have Mellanox ConnectX EN MNPH28B-XSC following main features: For safety warnings in German see Sicherheitshinweise Warnings in German on page Over-temperature This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: To guarantee proper air flow, allow at least 8cm 3 inches of clearance around the ventilation openings. During Lightning - Electrical Hazard During periods of lightning activity, do not work on the equipment or connect or disconnect cables. Refer to the cable manufacturer for special warnings and instructions.
Equipment Installation This equipment should be installed, replaced, or serviced only by trained and qualified Mellanox ConnectX EN MNPH28B-XSC. Equipment Disposal Disposal of this equipment should be in accordance to all national laws and regulations. Local and National Electrical Codes This equipment should be installed in compliance with local and national electrical codes.
ConnectX EN Dual Port Ethernet Network Interface Cards with SFP+ Connectors User s Manual - PDF
The green LED, when lit, indicates that the driver is running and a valid physical connection between nodes exists. If the green LED is blinking, it Mellanox ConnectX EN MNPH28B-XSC a problem with the physical link. The yellow LED when lit, indicates a valid data activity link, this is the logical link.
The yellow LED lights up when the network is discovered over the physical link. A valid data activity link without data transfer is designated by a constant yellow LED indication.
Mellanox ConnectX EN MNPH28B-XSC - network adapter
A valid data activity link with data transfer is designated by a blinking yellow LED indication. If the LEDs are not active, either the physical link or the logical link or both connections have not been established.
- Mellanox ConnectX EN MNPH28B-XSC - network adapter Overview - CNET
- ConnectX EN Dual Port Ethernet Network Interface Cards with SFP+ Connectors User s Manual
- Mellanox デバイスドライバのダウンロード
See Appendix A, Specifications, on page 34 for the location on the board. ConnectX EN Dual Port Ethernet Network Interface Cards With PCI Express x8 User's Manual. 3 Table Specifications for MNPH28B-XSC. MNPH28B-XSC, Rev X1/X2/X3/A1: MT_0BE, ConnectX® EN network interface card, dual-port, 10GBASE SFP+, PCIe x8 GT/s, mem-free, short.